Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Zolorr Zololl
Country: Monaco
Language: English (Spanish)
Genre: Art
Published (Last): 5 March 2009
Pages: 170
PDF File Size: 18.94 Mb
ePub File Size: 17.34 Mb
ISBN: 348-9-93130-278-3
Downloads: 32926
Price: Free* [*Free Regsitration Required]
Uploader: Akinocage

When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: Should say Step 1 Enable the mgmt 0 interface. Page shows with 8 base ports 8 licensed for growth. This is not correct as this does not work. Page Figure shows incorrect ip default-gateway Page States in one bullet: Page Document states: About System Message Logging properly configured system message logging server. Previous blog entries also dealt with storage, compute, virtualization and professional services.

I am not sure if this is valid.

On the same page I find this block of text very vague and confusing: From time to time I will blog about other things of interest.

This page incorrect states that fcns reject-duplicate-pwwn is disabled by default. The default authentication port is Cisco Documentation vonfiguration has internally re-written this as: There is no information contained in the example given that shows the configuration or enabling of FCIP interfaces.

These pages talk about an active mes of fcanalyzer. Testing indicates that this is in fact enabled by default. This can mean several configuration tasks for each iSCSI host. The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.


You must be logged in to giide a comment. This is very redundant and can be combined configurayion one bullet. Have a few different people read that and I think you will see where I am coming from.

This situation can require several configuration tasks for each iSCSI host. This should be made more clear. You do not need to restart the fcdomain. I think what is meant here is: Proudly powered by WordPress. If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration.

FCIP uses different ports.

Although it can be configured it has no effect. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur. This blog is mostly about my pursuits in Data Science. IP routing does not have to be enabled, unless there is a specific topology where IP routing is necessary. You cannot mix ingress and egress interfaces in the same SPAN session.

The autoreconfigure option takes immediate effect at runtime.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

Caution The span drop-threshold can be changed configuratin if no span sessions are currently active on the switch. Obviously there was a part of this paragraph that got chopped off somewhere. If you assign port number for physical portshow can you assign confkguration ports ?


You can nondisruptively reconfigure the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap. I am not sure. This is not correct. Page Information is repeated twice on the same page: Reconfiguration as in changing of domains is always disruptive.

In this case, using the proxy initiator mode simplifies the configuration. It is worded as if it is a requirement but it is in fact not.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

The opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer. A disruptive reconfiguration may affect data traffic. This is not true. This page incorrectly states that you can disable password verification with aaa authentication login none command.

Should be 8 base ports, which can goto 8 or 16 additional ports. Certainly there is either a mistake in the wording or the example.

Then states two bullets later: I am not sure that the statement in bold is correct. This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator.